MAXWELL 2G Mixed Switch: Toggle and Dimmer Setup Guide

Start with the control layout, not the wiring

The MAXWELL 2G Paintable Mixed Switch puts one toggle and one dimmer on a single antique brass plate. That combination is the reason to choose it: you get a hard on/off for a light you always switch, and a dial for a light you want to dim. Before you touch a screwdriver, decide which gang controls which circuit and whether the dimmer will sit on the side you naturally reach for.

The plate is slim, flat and low-profile, and the toggle and dial are turned from solid brass in an antique brass finish. The paintable plate means you can take the finish toward your wall colour, but the brass controls stay exposed. Plan the paint line before installation so the plate reads as part of the room rather than a masked-off afterthought.

What the MAXWELL 2G mixed switch includes

• MAXWELL 2G Paintable Mixed Switch 1Toggle/ 1Dimmer - Antique Brass: 2-gang antique brass paintable mixed light switch with 1 toggle and 1 dimmer on one plate, finish-matched to brass cabinet hardware. Confirms the gang count and the mixed control layout, so you can match it to a two-circuit room without adding a separate dimmer.

  

• MAXWELL 2G Paintable Mixed Switch 1Toggle/ 1Dimmer - Antique Brass: The dimmer uses auto-detect leading or trailing edge dimming for smooth, flicker-free control with modern LEDs. Auto-detect is the feature that decides whether your LED load is likely to behave; check your lamps against it before wiring.
• MAXWELL 2G Paintable Mixed Switch 1Toggle/ 1Dimmer - Antique Brass: Fully modular toggles and dimmers combine across 1-, 2-, 3- and 4-gang plates, all finish-matched. If your room grows or the layout changes, the same family can be rebuilt across other gang sizes without changing finish.

A safe order for the installation

The supplied product record does not include terminal-by-terminal wiring instructions, so treat the steps below as the planning and handling sequence around the switch rather than a wiring diagram. If you are not confident isolating the circuit, use a qualified electrician.

1. 1. Isolate the circuit: Switch off the relevant breaker and confirm the circuit is dead before removing the old plate. The product evidence does not supply an isolation procedure, so follow your own safe electrical practice.
2. 2. Confirm the two circuits: Identify which cable feeds the toggle light and which feeds the dimmer light. The mixed plate needs one switched circuit for the toggle and one dimmable circuit for the dimmer.
3. 3. Check the dimmer load: The dimmer auto-detects leading or trailing edge for modern LEDs. Confirm the lamps on the dimmer circuit are dimmable and that the load is within the dimmer's rating; the supplied record does not list a wattage, so check the dimmer module labelling before connecting.
4. 4. Mount the plate and controls: Fit the slim, flat plate and the brass toggle and dial. Keep the brass parts free of paint and filler while the plate is being finished.
5. 5. Restore power and test: Switch the breaker back on and test the toggle and dimmer separately. If the dimmer flickers or the LEDs behave poorly, the auto-detect circuit may not suit that lamp; stop and check compatibility rather than forcing it.

Painting the paintable plate without spoiling the brass

The plate is described as paintable, but the toggle and dial are solid brass in an antique brass finish. That combination sets the practical rule: paint belongs on the plate, not on the controls. Remove or carefully mask the brass toggle and dial before you paint, and keep the paint film thin around the edges so the plate still sits flat against the wall.

The antique brass finish is described as a rich, warm darkened brass with golden highlights, brushed and lacquered to hold its tone, backed by a 2-year guarantee. Solvent-heavy paint or aggressive sanding can undermine that lacquer, so work gently around the brass and wipe paint off the metal before it cures. The supplied information does not specify a paint type or a curing time, so follow the paint manufacturer's instructions rather than assuming a schedule.

Checkpoints before you close the wall

• Gang count matches the room: One toggle and one dimmer on a 2-gang plate; if you need a third control, the Maxwell family extends to 3- and 4-gang plates rather than adding a mismatched switch beside it.
• Dimmer circuit is genuinely dimmable: Auto-detect leading or trailing edge helps with modern LEDs, but it does not make non-dimmable lamps dimmable.
• Paint line is decided: The plate is paintable; the brass controls are not. Decide the paint edge before the plate goes on the wall.
• Finish continuity: The antique brass is finish-matched to brass cabinet hardware, so check it against nearby handles and sockets before committing the whole room.

Where the supplied evidence stops

The product record confirms the mixed layout, the auto-detect dimming, the modular plate family and the antique brass finish. It does not include terminal markings, torque figures, a wattage rating or a step-by-step wiring diagram. Those omissions are a limit of the supplied information, not a statement that the switch lacks them. If your installation depends on a specific terminal arrangement or load rating, confirm it against the dimmer module and the manufacturer's documentation before you begin.

For a straightforward two-circuit room, the MAXWELL 2G mixed switch is a practical way to keep a toggle and a dimmer on one antique brass plate. Plan the control layout, check the dimmer load, and protect the brass while you paint, and the installation stays focused on the decisions that actually change the result.